Eaton

Eaton Tripp Lite series SMART1500LCD

The official replacement pack for the SMART1500LCD is Eaton Tripp Lite RBC1500, a pre-assembled pack with two 12 V, 9 Ah VRLA batteries and an 18-month limited warranty (U.S. and Canada).

Official replacement cartridge

RBC1500

Official SKURBC1500
Voltage12 V (each); pack contains two 12 V batteries
Capacity9 AH (each)
TypeValve-regulated lead-acid (VRLA)
Batteries in the official cartridge2
Cartridge quantity1 pre-assembled pack
Cartridge warranty18-month limited warranty (U.S. and Canada — warranties may vary by country)
AssemblyShips fully assembled and ready for immediate installation; reusable packaging for recycling

Official RBC1500 product page

UPS specifications (from the official datasheet or product page)

Family / product nameEaton Tripp Lite series SMART1500LCD
VA rating1500 VA
Watt rating900 W
TopologyLine-interactive
WaveformEaton’s product copy describes “regulated sine wave output.” Confirm the owner’s manual for the exact on-battery waveform wording for your revision.
Input voltage120 V AC
Form factor2U rack / tower
Outlets8 × 5-15R
Runtime at half load11.8 minutes at half load
Runtime at full load4.4 minutes at full load (900 W)
User-replaceable batteryYes (official battery-replacement SKU published)
UPS warranty (as published)3-year limited warranty (U.S., Canada, and Mexico — warranties may vary by country); $250,000 Ultimate Lifetime Insurance (U.S., Canada, and Puerto Rico only)

Related models

How to replace the battery

Eaton lists RBC1500 as the battery replacement on the official SMART1500LCD product page. Use the official pack, not a loose pair of unmatched 12 V batteries, unless Eaton’s instruction sheet for your unit says otherwise.

  1. Confirm the UPS catalog number is SMART1500LCD, or one of the other models officially listed on the RBC1500 page (SMART1200LCD, SMART1500LCDXL, SMX1500LCD).
  2. Read the SMART1500LCD owner’s manual and the instructions packed with RBC1500.
  3. If the official sheet does not clearly allow a live swap, shut the UPS down and unplug it first.
  4. Install the complete pre-assembled RBC1500 pack and use the reusable packaging to send the expired batteries to a recycling center.
  5. Restore power and let the new pack charge before judging runtime.

These are orientation steps, not a substitute for the manufacturer’s instruction sheet. Lead-acid UPS batteries can present electrical and chemical hazards.

Warranty considerations

Genuine vs third-party packs. This guide lists only the official manufacturer cartridge. Third-party kits are widely sold, but this site does not verify their dimensions, runtime, or safety against the OEM specification. Schneider Electric’s FAQ on genuine APC RBCs states that a non-APC battery may result in lower runtime, damage the UPS, create hazardous conditions, or void safety certifications, and that it will void APC’s Equipment Protection Policy. If you still consider an aftermarket pack, treat voltage, capacity, and physical fit as necessary starting points — not as proof of compatibility — and expect warranty terms to change.

When to replace the whole UPS instead

Where to buy (affiliate placeholders)

These are ordinary search links, not tracked affiliate tags. When a program is joined, replace the href and keep the data-affiliate attribute.

Search Amazon for Tripp Lite RBC1500 Affiliate placeholderSearch eBay for Tripp Lite RBC1500 Affiliate placeholder

Affiliate disclosure

FAQ

What is the official battery for a SMART1500LCD?

Eaton’s official SMART1500LCD specifications list “Battery replacement: RBC1500.” The official RBC1500 page describes a pre-assembled pack with two 12 V, 9 AH VRLA batteries.

Will RBC1500 fit a SMART1500LCDXL?

The official RBC1500 page lists SMART1500LCDXL among compatible UPS systems, along with SMART1200LCD and SMX1500LCD. Still confirm the catalog number on your unit.

Sources